We Take Care of Everything for You

Your Market
Do You want to certificate Your Product in a German, other European or Worldwide Market?
We check for You the Conformity of Your Product depending on its built-in interfaces (Bluetooth, WiFi, LTE, CAN, LIN, Automotive Ethernet, etc.)
Your Certificates
We prepare for You the Tests imposed by the Market Norms:
Electromagnetic Compatibility EMC, Wireless, RF module tests, CE Mark, FCC, EMC Directive 2014/30/EU, Radio Equipment Directive 2014/53/EU (RED), Low Voltage Directive 2014/35/EU and Safety
Testing House
We Partner with the most prestigious Testing Houses
CSA Group, 7 Layers, Cetecom, TÜV Süd, and Phoenix
to get for You the best Testing Package.
Your Costs
We negotiate for You the best deals with our Partners and offer You the best quotation.
Your Measurements We schedule Your measurements according to
Your Prototyping Plan
and take care of Your SOP date.

We Fully Certificate Your Bluetooth and Bluetooth Low Energy End Product

When Your End Product incorporates the wireless MCU along with an external circuitry such as an antenna, various matching components, ground plane…
You need more to get it certified on the Market of your choice!
Radio Testing (R & TTE / RED / FCC / ISED) according to the country-specific or harmonized Radio Standards (EN 300 328, FCC 15.247, RSS-210) to ensure electromagnetic compatibility.
Test Firmware with the right Bluetooth Stack configuration to achieve Direct Test Mode (DTM) and / or Production Test Mode (PTM).
Test the Host Controller Interface (HCI) for the right communication between the host and controller elements of the Bluetooth protocol stack
Test separately the continuous transmitter (TX) & receiver (RX) modes
Test the TX and RX with different RF stimulus – data-high-rates (DH) packets like DH1 / DH3 / DH5
Test different channels/frequencies for TX/RX (2402, 2440 (LE), 2441, 2480 MHz)
Test different output powers within the specified min – max power range of the device type
Test the adaptivity mode for compliance with EN 300 328 harmonization scheme
Test the radiation level with the original or a typical antenna
Build a reliable SMA antenna connection to the Device
EMC tests according to EN 301 489-1/-17
Assessment of the compliance with the basic restrictions related to human exposure to electromagnetic fields EN 62479
Safety tests according to EN 60950
Bluetooth RF-PHY testing (low energy)
Bluetooth interoperability (IOP) testing & listing

We Fully Certificate Your WLAN / WiFi Device

Test for applicable Radio Standards: EN 300 328, FCC 15.247 [2.4 GHz] and EN 301 893, FCC 15.407 [5 GHz]
Test for different WLAN modes (e.g., IEEE 802.11 b / g / n / a /ac)
Test different data rates according to the IEEE 802.11 Wi-Fi protocol summary (e.g. 2Mbps / 11Mbps / 54Mbps / 450Mbps / 866.7 Mbps / 1.73 Gbps)
Test different channel frequencies (2412 MHz / 2462MHz / etc.)
Test different channel widths (20 MHz / 40 MHz / 80 MHz / 160 MHz)
Test different output power within the min – max power range of the device
Test continuous transmitter (TX) and receiver (RX) modes
Test different duty cycles (<99% for FCC)
Test the adaptivity mode for compliance with EN 300 328 harmonization scheme
Test the radiation level with the original or a typical antenna
Build a reliable SMA antenna connection to the Device

We Fully Certify YOUR GSM, UMTS & LTE Devices

Test for applicable Radio Standards: EN 301 511 for GSM; EN 301 908 for UMTS & LTE
Test for FCC part 22/24
Test mobile phone SIM locks
Test mobile terminated packet switched call from base
Test of the AT control commands
Establish a mobile originated packet switched call
Test the radiation level with the original or a typical antenna
Build a reliable SMA antenna connection to the Device
Test spurious emissions for GSM, UMTS, 2G/3G/4G
Test EMC to EN 301 489 -1/-52
Test safety according to EN 62368
RF exposure evaluation according to EN 62311

We Conduct Your Proof of Conformance for CAN, LIN, and Automotive Ethernet

CAN High-Speed and CAN-FD Conformance Tests

Perform the test cases defined in ISO11898-2:2016 and ISO 16845-2
Perform CAN-FD tests according to the new international standards ISO 16845-1 and ISO 16845-2

LIN (Local Interconnect Network)

Physical Layer Tests for LIN 2.1 as Master & Slave Node
Data Link Layer Tests / NCNM for LIN 2.1 as Master & Slave Node

Automotive Ethernet (BroadR-Reach)

tests according to the OPEN Alliance BroadR-Reach® (OABR) physical layer standards (IEEE 100BASE-T1)
PHY features set-tests (signal quality + cable diagnosis tests) OABR
Wake-up/sleep tests OABR
Layer 2 tests: IEEE Ethernet MAC + VLAN (802.1Q) + Address Resolution Protocol (ARP)
Layer 3 tests: Internet Provider Security (IPS) + Internet Control Message Protocol (ICMP)
Layer 4 tests: User Datagram Protocol (UDP) + Transmission Control Protocol (TCP) + Dynamic Host Configuration Protocol (DHCP)
Layers 5, 6 and 7 tests: Scalable Service-Oriented Middleware over Internet Protocol (SOME/IP) + Software Distributor (SD)
Link status and link-up tests (for links between advanced driver assistance systems,
infotainment, cameras, and other electronic control units)